Flocculants · CAS 9003-05-8 · From China
Anionic, cationic or nonionic — pick the wrong charge and a container of polyacrylamide does absolutely nothing in your water. No half-results, no partial refund from physics. So we never sell PAM by the datasheet. We match the ionic type, charge density and molecular weight to your sludge or slurry, prove it with a 500 g jar test, and only then load the container.
Orders shipped
Countries served
Product categories
Years sourcing China
Why PAM Buying Is Different
Most chemicals fail gradually — a weaker coagulant just needs a higher dose. Polyacrylamide fails absolutely. A cationic sludge needs a cationic polymer; feed it an anionic grade and the charges repel, the flocs never form, and twenty tons of white powder becomes landfill. The same goes for charge density and molecular weight: a low-charge polyacrylamide on a high-solids centrifuge, or a mid-weight polymer on fast-settling sand tailings, gives you cloudy water and a supplier who insists the product "passed QC" — because it did. It was simply the wrong grade for your water, and no certificate protects you from that.
That's why this page is built around two things: the selection matrix below, which gets you to the right ionic family, and the jar test, which proves the exact grade on your actual water before any container is booked.
Anionic · Cationic · Nonionic
Find your application on the left. The columns are the ionic type, the charge density band, the molecular weight tier and the dosing magnitude your process typically runs at. These are the starting points — the jar test settles the final grade.
| Your application | Ionic type | Charge density | Molecular weight | Typical dosing |
|---|---|---|---|---|
| Municipal sludge dewatering belt press / centrifuge | Cationic | 40–60% for belt press · 60–80% for high-solids centrifuge | Medium–high · 8–12 million | 2–8 kg per ton of dry solids |
| Textile & dye wastewater after PAC coagulation | Anionic | Low–medium · 10–30% hydrolysis | High · 12–18 million | 1–3 g/m³ of effluent |
| Sand-washing tailings wash plants, aggregates | Anionic | Medium · 20–30% hydrolysis | Very high · 16–22 million | 5–30 g/m³ of slurry |
| Paper retention & drainage | Cationic Nonionic | Low · 10–20% | Medium · 6–10 million | 0.2–0.5 kg per ton of paper |
| Drilling mud PHPA fluid systems | Anionic | 25–30% hydrolysis (PHPA) | High · 12–16 million | 1–3 kg/m³ of mud |
| Mineral-processing tailings thickeners, mine water | Anionic | Medium · 15–30% hydrolysis | Very high · 18–22 million | 20–100 g per ton of solids |
Mixed or unusual water? Oily, high-salinity and food-processing effluents often sit between rows — that's exactly what the jar test is for.
Describe your water — we'll shortlist the gradesSee The Actual Product
The Material
White translucent PAM beads — the ionic type and molecular weight are what actually matter, not the look.
How It Ships
Palletised 25 kg bags from our partner's stock — full lots ship together, not scraped from a trader.
Proven First
A 500 g jar test on your own water clears it before a container is ever committed.
Prove It Before You Buy It
This is the whole discipline of buying polyacrylamide: never order twenty tons of a grade that hasn't beaten its rivals in a beaker of your own water. The cycle takes about two weeks door to door.
Describe your water
Application, dry-solids %, current chemical and dose if any. A phone photo of the sludge or slurry genuinely helps.
We shortlist 2–3 grades
From the matrix, bracketing your case — e.g. one medium-charge and one high-charge cationic polyacrylamide.
500 g samples ship by courier
Free sachets, labelled per grade, to Central Asia, South America, the Middle East, Africa or Southeast Asia in about a week.
Run the jar test
Make a 0.1% stock solution, dose stepwise, watch floc size, settling speed and water clarity. A one-page protocol comes with the samples.
Lock the grade, load the container
The winning sample's production spec becomes your contract spec. Every future lot is checked against it.
Salt-Cut & Stale Stock
The two classic frauds in this trade are cutting polyacrylamide powder with cheap inorganic salt, and shipping degraded stock that has sat in a humid warehouse for two years. Neither shows up on the seller's own paperwork. All three checks below work with a beaker and a stopwatch.
Real powder PAM at 0.1% needs roughly 40–60 minutes of stirring to dissolve into a smooth, viscous solution.
Walk away
Dissolves in minutes → salt-cut. Never dissolves, leaves permanent "fish-eye" lumps → degraded or cross-linked junk.
Healthy sign
Slow, even hydration ending in a clear, stringy solution.
High-molecular-weight polyacrylamide builds large, dense flocs that settle fast and survive gentle stirring.
Walk away
Small, fluffy flocs that shear apart when stirred → low molecular weight sold as high, or stock past its life.
Healthy sign
Big flocs, fast settlement, clear supernatant at the datasheet dose.
Fresh polyacrylamide powder is nearly odourless. As it degrades it hydrolyses and releases ammonia.
Walk away
A sharp ammonia hit when you open the bag → old or badly stored stock, already losing activity.
Healthy sign
No smell, dry free-flowing granules, production date on the bag under six months old.
We run these checks at the factory, and you can have an independent third-party pre-shipment inspection repeat them before the balance payment.
Get inspected, dated stockReading The Quotes
Two quotes for "PAM, 25 kg bags" can sit far apart and both be honest — because polyacrylamide isn't one product. The grade you locked in the jar test defines most of the cost: a 70%-charge cationic polymer and a 15%-hydrolysis anionic one are almost different chemicals. When a quote looks impossibly cheap for the grade you asked for, the usual explanation isn't generosity — it's a lower charge, a lower molecular weight, or the salt bag from the section above.
We quote against your locked spec, name the factory, and put the measured values on the COA — so you're comparing the same molecule, not the same three letters.
— Matt, XILINK founder · 13 years sourcing & exporting industrial products from China
Send Your Water Type & Specs — Reference Price In 24hThe four levers behind every PAM quote
Acrylamide monomer market
The feedstock sets the floor for every producer. It moves month to month — which is why we quote a current-month reference price, not a number carved on a webpage.
Molecular weight
Higher molecular weight means longer, more tightly controlled polymerisation. A 20-million grade always costs more than a 10-million grade.
Cationic charge density
The cationic co-monomer costs a multiple of acrylamide, so price climbs steeply with charge — a 60% cationic polyacrylamide sits far above a 20% one.
Powder vs emulsion
Powder is ≥88% active — the cheap way to ship. Emulsion dissolves faster but is 30–40% active, so part of your ocean freight is water.
What We Ship
Every lot ships with a certificate of analysis carrying the measured values — solid content, molecular weight, charge — against your locked spec, plus the production date you saw on the bags. Independent third-party inspection before the balance payment is available on any order.
You don't have to fill a container with one product. A trial order of polyacrylamide from 1 ton rides alongside polyaluminium chloride (PAC) and other water-treatment chemicals in the same box — one container, one set of documents, one bill of lading to your port, whether that's in Central Asia, South America, the Middle East, Africa or Southeast Asia.
Running a full dosing line? See the whole water-treatment chemicals range we consolidate from China.
| CAS number | 9003-05-8 |
| Form | White granular powder · emulsion grades on request |
| Solid content | ≥ 88–90% (powder) |
| Molecular weight | 5–22 million, by grade · anionic up to 22M, cationic typically 8–12M |
| Ionic families | Anionic 10–35% hydrolysis · cationic 10–80% charge · nonionic |
| Packaging | 25 kg laminated kraft bags with inner PE liner · palletised & shrink-wrapped or floor-loaded to suit your port |
| Shelf life | 24 months dry storage · production date printed on every bag |
| Trial order | From 1 ton · consolidates with PAC & other chemicals in one container |
| Documents | Per-lot COA · MSDS · third-party inspection on request |
Straight Answers
Trial orders start from 1 ton. You don't need a full container of one grade — PAM consolidates with PAC and other water-treatment chemicals in the same box, so a first order can be a mixed pallet-load that lets you validate the grade and the supply chain before committing to volume.
Describe your water and we shortlist two or three candidate grades, then courier 500 g sachets of each with a one-page jar-test protocol — free of charge. Most destinations receive them within about a week. You test on your own water, lock the winning grade, and that sample's production spec becomes the contract spec.
Yes. Every lot ships with a certificate of analysis carrying measured solid content, molecular weight and charge against your locked spec, plus MSDS. On request we arrange an independent third-party inspection — dissolution check, floc test, bag dates, weights — before your balance payment, not after arrival.
Yes — it's the most common combination we load. Both are non-dangerous goods in 25 kg bags, palletised together with one set of shipping documents. Coagulant plus flocculant in one container is how most treatment plants and dealers actually buy, and it spreads the ocean freight across the whole order.
Common anionic and cationic grades are usually produced within 7–15 days of order confirmation; freshly made stock beats warehouse stock for a product that degrades with age. Ocean transit depends on your route and is confirmed with the quote. For repeat buyers we schedule staggered shipments so the dosing room never runs dry.
Matched, Tested, Loaded
Tell us what you're treating — sludge, tailings, effluent — with whatever numbers you have. We come back within 24 hours with the shortlisted polyacrylamide grades, the sample plan and the current-month reference price.
Free 500 g jar-test samples before any container
Prefer chat? Message us on WhatsApp
Thank you — within 24 hours you'll have the shortlisted grades, the sample plan and the current-month reference price.
Please message us on WhatsApp and we'll pick it up right away.